Annual testing
Open the annual page when the utility notice is about routine testing, timing, and accepted submission methods.
special utility district
Talty Special Utility District Backflow Testing backflow testing requirements
Talty SUD is a strong district example because it publishes explicit annual testing triggers, deadline months, RPZ rules for OSSF properties, and a hard service-disconnection consequence for noncompliance.
Testing cadence: Upon installation and annually for health-hazard or commercial properties
Last verified: 2026-06-29
Verification code: TL
Freshness window: 45 days
Next-step paths
Start with the page that matches your situation
This page is the rule hub. Use it to confirm the governing utility workflow, then open the focused page that matches the actual situation on site.
Failed test
Open the failed-test page when the device already failed and you need the repair, retest, and reporting order.
Irrigation
Open the irrigation page when the question is tied to sprinkler systems, reclaimed water, or landscape devices.
View the official tester list
Use the published tester route after you confirm the rule, due basis, and submission path on this utility page.
Annual or event-based timing
Irrigation systems, commercial properties, properties with onsite sewer facilities or septic systems, and customers served by Talty Special Utility District who have testable backflow assemblies.
- Upon installation and annually for health-hazard or commercial properties
- Talty SUD says irrigation assemblies are tested upon installation and the test form must be provided to the district office. The district also requires annual testing for assemblies protecting against a health hazard and for all commercial properties regardless of health hazard, with test results due by either May 1 or November 1 depending on the cycle.
Non-compliance penalties
Talty SUD says failure to complete testing and send results by the deadline will result in disconnection of service. The district also says service remains disconnected until compliance is met and outstanding balances are paid.
- Talty treats OSSF properties as health hazards and requires RPZ protection, which can turn a failed DCV into a replacement project instead of a simple retest.
- The district uses hard deadlines and says missed results can lead to disconnection of service.
- A tester can be licensed and still unusable for the job if they have not registered with the Talty office.
Compliance workflow
Official workflow
Every focused page on this utility still runs through this authority sequence. Confirm the rule here before you branch into repair, testing, or provider routing.
- Use Talty's backflow page to confirm whether the property is installation-only or part of the annual testing cycle.
- If the property has an irrigation system, complete the permit and inspection workflow through the district office first.
- Hire a tester who is registered with the Talty SUD office and uses a current gauge certification.
- Send the completed report to the district office by the May 1 or November 1 deadline tied to the property cycle.
Source block
Talty SUD is strong file-backed pilot material because it publishes installation testing, annual health-hazard and commercial testing, OSSF-to-RPZ rules, hard May 1 or November 1 deadlines, an official tester list, a report form, and a registration form.
- Last verified: 2026-06-29
- Verification code: TL
- Freshness window: 45 days
- Report a correction or stale source
- Talty SUD backflow page official program page
- Talty SUD irrigation page official irrigation guidance
- Talty SUD tester list official pdf
- Talty SUD backflow test form official pdf
- Talty SUD tester registration form official pdf
Submission methods and utility contact
Where the rule applies
- Irrigation systems
- Commercial properties regardless of hazard class
- Properties with onsite sewer facilities or septic systems
- Developments served by Talty Special Utility District
Devices in scope
- Inline testable backflow devices
- Double check valve assemblies
- Reduced pressure zone assemblies
Residential notes
- Talty SUD is more nuanced than a blanket annual rule: some residential developments now only require an initial irrigation test, while OSSF and other health-hazard properties stay in the annual lane.
- Residential owners should not assume the relaxed rule applies everywhere, because Talty still requires annual testing when the property is a health hazard.
Commercial and managed properties
- Talty says commercial properties are annual regardless of health hazard, which makes the district stricter than a basic residential sprinkler explanation.
- Commercial accounts also face a more direct operational consequence because Talty explicitly ties missed deadlines to disconnection.
FAQ
Local questions people actually ask
Does Talty Special Utility District Backflow Testing require annual backflow testing?
Upon installation and annually for health-hazard or commercial properties. Talty SUD says irrigation assemblies are tested upon installation and the test form must be provided to the district office. The district also requires annual testing for assemblies protecting against a health hazard and for all commercial properties regardless of health hazard, with test results due by either May 1 or November 1 depending on the cycle.
Who is affected by Talty Special Utility District Backflow Testing backflow rules?
Irrigation systems, commercial properties, properties with onsite sewer facilities or septic systems, and customers served by Talty Special Utility District who have testable backflow assemblies.
How do I submit or confirm a backflow test for Talty Special Utility District Backflow Testing?
Use the official utility workflow and submission methods listed on this page: Talty SUD backflow page, Talty SUD irrigation page, Talty SUD backflow test form, Talty SUD tester registration form. Program phone: 972-552-4422.
Where should I look for testers for Talty Special Utility District Backflow Testing?
Start with the governing authority's published tester list. This utility has an official approved-tester route and it should be treated as the primary source.
Need a tester or local help?
Start with the governing authority's published tester list. Use provider help only after the official rule, due basis, and submission path are clear.
Market cost analysis
Local cost band
Typical testing and repair pricing used to frame next-action decisions in the metro around this utility.
Provider browse layer
Public provider direction
Provider routing stays clearly labeled below the official workflow. This block exists to frame public provider discovery without implying authority status.
Local testing profiles
Use provider profiles and metro pages only after confirming the utility workflow and list rules above.
Public directory stays separate
Provider help is reviewed separately from the official utility workflow and never replaces the authority guidance above.