Routes for "dallas"
Open the most specific city or utility route first. Portal hubs help when the notice names a software system but the local utility still controls the rule.
Dallas backflow notice route
Dallas maps to Dallas Water Utilities Backflow Prevention Program. Report acceptance depends on using the named portal or online submission path; keep proof that the report was submitted.
- Portal: SwiftComply
- Due basis: Dallas Water Utilities says high-hazard assemblies require annual testing by a licensed tester registered with the City of Dallas, while lawn irrigation devices are tested when newly installed, repaired, or replaced. Failed devices get a 30-day repair and retest window and submissions run through SwiftComply.
- Fee clue: Dallas is clearer on compliance workflow and portal fees than on consumer-facing quote ranges.
- Failed-test clue: Do not assume all Dallas assemblies are annual; irrigation has a narrower trigger.
Dallas Water Utilities Backflow Prevention Program workflow
Dallas is a useful edge case because it is not simply annual-for-everything: high-hazard assemblies are annual, irrigation is event-driven, and SwiftComply is mandatory for covered test reports.
- Portal: SwiftComply
- Due basis: Dallas Water Utilities says high-hazard assemblies require annual testing by a licensed tester registered with the City of Dallas, while lawn irrigation devices are tested when newly installed, repaired, or replaced. Failed devices get a 30-day repair and retest window and submissions run through SwiftComply.
- Fee clue: Dallas is clearer on compliance workflow and portal fees than on consumer-facing quote ranges.
- Failed-test clue: Do not assume all Dallas assemblies are annual; irrigation has a narrower trigger.
Garland backflow notice route
Garland maps to City of Garland Water Supply Protection. Report acceptance depends on the governing tester route and the utility's submission method; confirm status before scheduling.
- Tester gate: official list
- Due basis: Garland says all backflow prevention assemblies shall be tested according to TCEQ regulations prior to permanent activation of the plumbing system and annually thereafter. Test reports must be submitted to Garland Water Utilities within 10 days of the test.
- Fee clue: Garland publishes a $88 irrigation permit fee, a $75 annual tester-registration fee, and a $25 test-form booklet fee on the official workflow. The tester-side fees matter even if the property owner only sees the final quote.
- Failed-test clue: Garland uses a short 10-day report window after testing.
Grand Prairie backflow notice route
Grand Prairie maps to Grand Prairie Water Utilities. Report acceptance depends on the governing tester route and the utility's submission method; confirm status before scheduling.
- Tester gate: official list
- Due basis: Backflow assemblies enrolled in the local cross-connection program must be tested annually and submitted through the utility workflow.
- Fee clue: Commercial hazard class, emergency scheduling, and device accessibility change the final price.
- Failed-test clue: A failed assembly typically needs repair plus a documented retest.
Irving backflow notice route
Irving maps to City of Irving Cross Connections and Backflow. Report acceptance depends on the named portal and the utility-approved tester route; keep proof that the report was submitted.
- Portal: VEPO/Envirotrax
- Tester gate: official list
- Due basis: Irving requires backflow test reports to be submitted online through Envirotrax within 10 days of the test date, with permit verification needed for newly replaced or installed assemblies before testing.
- Fee clue: Irving's public cost signal is more about avoiding late or incomplete Envirotrax reporting than retail test price.
Mesquite backflow notice route
Mesquite maps to City of Mesquite Backflow Prevention. Report acceptance depends on the governing tester route and the utility's submission method; confirm status before scheduling.
- Tester gate: official list
- Due basis: Mesquite says all backflow prevention assemblies must be tested upon installation and thereafter annually by a licensed backflow tester, excluding residential assemblies that require testing upon installation. The tester must be registered with the City, contact the Backflow Inspector before testing, and complete the observed test appointment.
- Fee clue: Mesquite's residential irrigation guide also lists a $125 irrigation permit fee, which means the City-side cost stack matters before the contractor invoice is even considered.
- Failed-test clue: Mesquite requires the inspector to be present for testing, so a test can still fail procedurally even if the device itself passes.
City of Garland Water Supply Protection workflow
Garland is a strong pilot utility because it publishes the annual cadence, 10-day report rule, tester-registration workflow, irrigation permit details, and fire line registration requirements on official pages.
- Tester gate: official list
- Due basis: Garland says all backflow prevention assemblies shall be tested according to TCEQ regulations prior to permanent activation of the plumbing system and annually thereafter. Test reports must be submitted to Garland Water Utilities within 10 days of the test.
- Fee clue: Garland publishes a $88 irrigation permit fee, a $75 annual tester-registration fee, and a $25 test-form booklet fee on the official workflow. The tester-side fees matter even if the property owner only sees the final quote.
- Failed-test clue: Garland uses a short 10-day report window after testing.
City of Irving Cross Connections and Backflow workflow
Irving is a strong Envirotrax page because it publishes a 10-day online submission rule, failed-test customer notice requirement, permit verification for replacements, and tester credential maintenance.
- Portal: VEPO/Envirotrax
- Tester gate: official list
- Due basis: Irving requires backflow test reports to be submitted online through Envirotrax within 10 days of the test date, with permit verification needed for newly replaced or installed assemblies before testing.
- Fee clue: Irving's public cost signal is more about avoiding late or incomplete Envirotrax reporting than retail test price.
City of Mesquite Backflow Prevention workflow
Mesquite is a strong pilot utility because it clearly publishes annual-vs-residential cadence, inspector-witnessed testing, the official tester list, and separate commercial, irrigation, and fire line assembly rules.
- Tester gate: official list
- Due basis: Mesquite says all backflow prevention assemblies must be tested upon installation and thereafter annually by a licensed backflow tester, excluding residential assemblies that require testing upon installation. The tester must be registered with the City, contact the Backflow Inspector before testing, and complete the observed test appointment.
- Fee clue: Mesquite's residential irrigation guide also lists a $125 irrigation permit fee, which means the City-side cost stack matters before the contractor invoice is even considered.
- Failed-test clue: Mesquite requires the inspector to be present for testing, so a test can still fail procedurally even if the device itself passes.
Grand Prairie Water Utilities workflow
Annual testing is required for enrolled backflow prevention assemblies in the Grand Prairie utility program.
- Tester gate: official list
- Due basis: Backflow assemblies enrolled in the local cross-connection program must be tested annually and submitted through the utility workflow.
- Fee clue: Commercial hazard class, emergency scheduling, and device accessibility change the final price.
- Failed-test clue: A failed assembly typically needs repair plus a documented retest.